Grillo G Z3

413.000 HUF +VAT

Bács-Kiskun county, 6000 Kecskemét

Sharing:

5

Description
G Z3 is reliable, simple and safe!
Milling the soil, even hard, becomes easy and guarantees a job well done!
The G Z3 is equipped with forward and reverse drive, 80 cm wide cutting deck and Honda GCV170 engine.

The G Z3 is a compact power tiller that is ideal for light tillage, even where space is at a premium.
The 6 star hoe is 80 cm wide, and can be narrowed to 57 and 35 cm by removing 2 or 4 hoe stars.

The Grillo G Z3 is equipped with an active clutch; the lever on the handlebar, when pressed, starts the rotation of the hoes. When the lever is released, the tines stop immediately but the motor continues to run.
The side plates should not be used when working on hard ground that has never been worked.

On softer soils, side discs are very useful: they help maintain direction, move forward and protect neighbouring crops from being tilled.

Two spurs are supplied as standard: one for soft soil and one for hard soil. The blade setting determines the working depth.
When the spur is set low, the tines sink deeper into the soil.

With the spur set high, the centre of gravity moves forward, so the car moves faster.
The use of side discs and high spurs increases flotation and forward progress.
G Z3 is fast, stable and precise!
The gearbox is equipped with oil bath gears and designed to last for a long time. Built entirely in Grillo's factories.

The 4,8 HP engine guarantees sufficient torque for milling at 2400 rpm! Depending on the ground conditions and the amount of crumbling you want to achieve, you can chop slowly at 80-90 rpm or quickly at up to 155 rpm.
The power of the engine is no limit to the G Z3 even in the deepest operations, when the cutter is at maximum width and fully buried!
The steering wheel can be adjusted laterally without stopping. There are no screws or knobs to loosen and then tighten. Essential equipment if you don't want to step on the ground you are working on or if you are milling near hedges, fences or under branches.

The height-adjustable handlebars meet the needs of all users and there is always the right position for every milling depth.
In addition, the lower handlebar position is useful for transporting the G Z3 on the standard front transfer wheel.

The groove is attached to the back of the handlebar with a spring pin in place of the spur, so no tools are required for installation.
Working with the tiller, you can make regular furrows for watering or seeding.

Cleaning and maintenance is extremely easy! Just check the engine oil level regularly and clean the filter. The gearbox requires no maintenance. The G Z3, like all Grillo products, is designed and built to last and retain its value over time. All components, from the simplest to the most complex, are of the highest quality. The Grillo G Z3 is equipped with a latest generation engine with a Ready Start device for quick and easy starting! All engines are fitted with top valves to minimise fuel consumption, emissions, noise and vibration. Frame, handlebars, cutter, everything is built by Grillo in Italy, using the best materials and the most modern technologies to ensure high, consistent and 100% controlled quality.

The hardened steel tines are removable.
Grillo machines are painted with two coats of electrostatic powder. First the wash and prep baths are applied, followed by the first protective coat, which together with the kiln firing process forms the best base for the finishing coat. A second coat of varnish and a further baking at 190 °C gives the characteristic hardness and gloss.
All machines are carefully assembled and thoroughly tested by qualified personnel. The final test is done with the engine running!

Grillo products are distributed and supported throughout the country by a network of specialised Grillo retailers. Spare parts are available after many years of service.

**Technical data sheet**
**G Z3 Technical Data Sheet**
**Engine:** Honda GCV170 OHC
Manual self-restart
**Fuel type:** Petrol
**Displacement:** 166 cc, 1 cylinder
**Power:** 4.8 HP (3.6 kW)
Air-cooled
Dry air filter with replaceable cartridges
** Fuel tank capacity:** 0,9 l
**Extraction:** by auger, in oil bath
**Shift:** 1 forward and 1 reverse
**clutch:** actively engaged
**Cutter:** 6 stars + side plates, working width 75 cm
**Head diameter:** 28 cm
**Working width with side plates:** 80 cm, adjustable to 57 and 35 cm.
**Working width without side plates:** 75 cm, adjustable to 52 and 30 cm.
**Working depth:** 28 cm
**MAX cutting speed:** 155 rpm
**Handlebar:** Adjustable in height and laterally
**Wheel equipment:** Front transfer wheel. Two spurs, one for hard ground and one for soft or sandy ground.
**Safety devices:** Active coupling: when the handle is released, the cutter stops. Fenders and handlebars are compatible. Silencer protection
**Weight:** 45 kg