Grillo G Z2

360.000 HUF +VAT

Bács-Kiskun county, 6000 Kecskemét

Sharing:

4

Description
G Z2 is reliable, simple and safe!
Milling the soil, even hard, becomes easy and guarantees a job well done!
The G Z2 is equipped with forward and reverse drive.

The G Z2 is a compact power tiller that is ideal for light tillage, even where space is limited.
The 4-star hoe is 57 cm long.
With the optional tiller set, you can make only 2 hoe stars with a working width of 35 cm, and 6 hoe stars with a width of 80 cm.

The Grillo G Z2 is equipped with an active clutch; the lever on the handlebar, when pressed, starts the rotation of the hoes. When the lever is released, the hoes stop immediately but the motor continues to run.
The side plates should not be used when working on hard ground that has never been worked.

On softer soils, side discs are very useful: they help maintain direction, move forward and protect neighbouring crops from being tilled.

Two spurs are supplied as standard: one for soft soil and one for hard soil. The blade setting determines the working depth.
When the spur is set low, the tines sink deeper into the soil.

With the spur set high, the centre of gravity moves forward, so the car moves faster.
The use of side discs and high spurs increases flotation and forward progress.
G Z2 is fast, stable and precise!
The gearbox is equipped with oil bath gears and designed to last for a long time. Built entirely in Grillo's factories.

The 3 HP engine guarantees sufficient torque for milling at 2400 rpm! Depending on the ground conditions and the amount of crumbling you want to achieve, you can chop slowly at 80-90 rpm or quickly at up to 155 rpm.
The power of the engine is no limit to the G Z2 even in the deepest operations when the cutter is at maximum width and fully buried!
The handlebar can be adjusted laterally without stopping. There are no screws or knobs to loosen and then tighten. Essential equipment if you don't want to step on the ground you are working on or if you are milling near hedges, fences or under branches.

The height-adjustable handlebars meet the needs of all users and always find the right position for any working depth.
In addition, the lowest setting is useful when the G Z2 is supplied on the standard front transmission wheel.
The G Z2 can also be transported in the boot of a car by lowering the handlebars.
Using the groove is a pleasure and you will always be satisfied with the result!

Cleaning and maintenance are extremely easy! Just check the engine oil level regularly and clean the filter. The gearbox requires no maintenance. The G Z2, like all Grillo products, is designed and built to last and retain its value over time. All components, from the simplest to the most complex, are of the highest quality. The Grillo is equipped with a latest generation engine with a Ready Start device for easy and quick starting! All engines are fitted with top valves to minimise fuel consumption, emissions, noise and vibration. Frame, handlebars, cutter, everything is built by Grillo in Italy, using the best materials and the most modern technologies to ensure high, consistent and 100% controlled quality.

The hardened steel tines are removable.
Grillo machines are painted with two coats of electrostatic powder. First the wash and prep baths are applied, followed by the first protective coat, which together with the kiln firing process forms the best base for the finishing coat. A second coat of varnish and a further baking at 190 °C gives the characteristic hardness and gloss.
All machines are carefully assembled and thoroughly tested by qualified personnel. The final test is done with the engine running!

Grillo products are distributed and supported throughout the country by a network of specialised Grillo retailers. Spare parts are available after many years of service.

**Technical data sheet**
**G Z2**
**Engine**: Briggs & Stratton 575EX OHV
Brbr.
**Fuel type**: petrol
**Displacement**: 140 cc, 1 cylinder
**Power**: 3 HP (2.2 kW)
Air-cooled
Dry air filter
**Fuel tank capacity**: 0,8 l
**Extraction**: by pulley, in oil bath
**Shift**: 1 forward and 1 reverse
**Clutch**: Actively engaged
**Cutter**: 4 stars + side plates, working width 52 cm
**Knife diameter**: 28 cm
**Working width with side plates**: 57 cm. With the optional kit, the cutter can be adjusted from 35 to 80 cm.
**Working width without side plates**: 52 cm. With optional kit, the cutter can be adjusted from 30 to 75 cm.
**Working depth**: 28 cm
**MAX cutting speed**: 155 rpm
**Handle**: Adjustable in height and laterally
**Wheel equipment**: Front transfer wheel. Two spurs, one for hard ground and one for soft or sandy ground.
**Safety devices**: Active coupling: when the handle is released, the cutter stops. Fenders and handlebars are compatible. Silencer protection
**Weight**: 41 kg